Three knots — bowline, figure-8, and Prusik — cover the core rope applications in a wilderness rescue scenario: creating a harness for hauling or lowering a person, establishing a secure anchor point, and ascending a fixed rope after a fall or for accessing a cliff or steep embankment. These are the knots with direct life-safety implications. This is a companion to the full 12-knot reference in survival knot tying: 12 knots every prepper must know.

Read this first: improvised rope rescue is not equivalent to rated rescue gear used by trained people. A harness tied from rope, an untested anchor, or cord that is not rated for life safety (paracord included) can fail or injure the person on it. If someone needs to be raised or lowered, call 911 and let a trained search and rescue team do it unless waiting is clearly more dangerous. Treat everything below as a last resort, and learn it from a qualified instructor on rated gear before you ever need it.

Bowline Seat Harness: Improvised Sit-Harness From One Rope

A commercial harness distributes load across the hip bones and thighs. An improvised seat harness using a bowline only roughly approximates this. It has no tested rating, is not a substitute for a commercial harness in any use, and should be used only for the shortest possible raise or lower when there is no other option.

Single-loop bowline seat harness (simple):

  • Tie a large bowline loop sized to go around both thighs when sitting — approximately 24–30 inches in diameter for an adult.
  • Step through the loop — both legs through, loop sitting under the buttocks like sitting in a swing.
  • The standing part (the rope coming from the bowline knot body up toward the anchor) becomes the hauling line. Pull force is taken across the bowline knot body and transferred through both loops to the thighs.
  • The person being hauled should hold the standing line above the bowline with both hands to stabilize their body angle and prevent tipping forward.

Swiss seat (more secure for longer operations):

  • Start with a 10–12 foot length of rope. Find the midpoint.
  • Place the midpoint against the small of the back. Bring both ends around to the front, crossing over the abdomen.
  • Pass each end between the legs, one on each side. Bring both ends back up to the front.
  • Thread both ends through the loops at the hip (front) and tie together with a square knot backed by two half-hitches. The attachment point is at the front hip-level cross.
  • Load rating: none. An improvised seat has no tested load rating. Use rope made and rated for life safety if you have it; paracord is not rated to hold a person.

One-Handed Bowline: Tying When One Hand Is Injured

If one arm is injured, the bowline can be tied one-handed by bracing the standing part against a fixed object:

  • Place the standing part around a tree or post at waist height, holding the working end in your functioning hand.
  • Form the small loop by flipping the working end over the standing part using your hand against the tree as a brace point.
  • Push the working end through the loop from behind, route around the standing part, and back through the loop — all with one hand and the tree as a third point.

  • Practice this before you need it. The one-handed technique takes many repetitions to learn.

Figure-8 on a Bight: Building the Anchor

The figure-8 on a bight is the preferred anchor knot for rescue scenarios because it is secure when dressed and set correctly and is easily visually inspected (the knot pattern is immediately recognizable when dressed correctly).

Redundant anchor setup using figure-8s:

  • For a single-person hauling anchor in the field, tie the figure-8 on a bight around the largest live, well-rooted tree available. We found no agency standard for a minimum trunk size, so do not rely on a number. Never anchor to a standing dead tree, a leaning tree, or a tree that shows signs of root damage.
  • For redundant rescue anchors (two-point equalized anchor): tie a figure-8 on a bight to each of two separate trees. Connect the two loops with a carabiner or a bowline tied around both loops. Two anchors give a backup if one fails; this simple setup does not guarantee the load splits evenly.
  • Test every anchor before committing a person to it: apply body weight progressively while watching the knot and anchor point. If anything moves or shifts, use a different anchor.

Prusik for Ascending a Fixed Line

A Prusik hitch on a fixed line allows ascending a rope without mechanical ascenders. This is a technical skill; learn it from a qualified instructor on rated rope and cord before relying on it. Two Prusiks are needed for ascending: one as a foot loop (stand up in it to gain height) and one as a chest or hip loop (sit back in it while repositioning the foot Prusik).

Two-Prusik ascending system:

  • Foot Prusik: Tie a Prusik loop in accessory cord thinner than the main line, long enough to stand in. Attach to the main line with 3 wraps. The loop end hangs below as a foot stirrup.
  • Body Prusik: Tie a second Prusik loop above the foot Prusik, sized to position the hand grip at chest height when standing in the foot Prusik.
  • Ascending sequence: Stand in the foot Prusik, slide the body Prusik up as high as possible. Sit back into the body Prusik (weight transfers from feet to body loop). Slide the foot Prusik up and stand again. Repeat.

Friction-hitch rappel backup: Climbers tie a friction hitch on the rope below the rappel device (often an autoblock rather than a Prusik) and hold it loosely in the braking hand so it slides during a controlled descent. If you let go, the hitch can grip the rope and stop the descent. A hitch that is tied wrong can fail to grab or can jam, so learn this from a qualified instructor.

Prusik failure modes: A Prusik loses grip when the Prusik cord is too close to the main line’s diameter; when the wraps are not parallel (tangled wraps reduce grip surface); and when the main line is icy or muddy (reduced friction). In icy conditions, use 4–5 wraps instead of 3.

Where to Go Next

The full 12-knot reference with load ratings and use cases is in survival knot tying: 12 knots every prepper must know. Shelter-building knot applications (ridgeline, tautline guyline, lashings) are in knots for shelter building: ridgeline, tautline, and lashing. If you need to treat an injury sustained during a rescue, the field wound care and fracture management articles are linked from wilderness first aid: 15 field-treatable emergencies.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *